Home > Socket Error > Error 10035

Error 10035


This can also result from connect, sendto, WSAConnect, WSAJoinLeaf, or WSASendTo when the remote address or port is not valid for a remote computer (for example, address or port 0). An address incompatible with the requested protocol was used. WSAEHOSTDOWN 10064 Host is down. WSAEDESTADDRREQ 10039 Destination address required. check over here

WSA_IO_PENDING 997 Overlapped operations will complete later. An MX record is returned but no A record—indicating the host itself exists, but is not directly reachable. Left by Lance Robinson on May 25, 2006 6:26 AM # re: Winsock error 10035 What about this error during recv? Left by Madhavi on May 25, 2006 12:12 AM # re: Winsock error 10035 The buffer doesn't have to be empty before you can send data - it just can't be

What Is A Socket Error

A call to the WSALookupServiceEnd function was made while this call was still processing. bobobobo Posted March 2, 2009 at 5:11 pm Permalink OK Now I think I understand this: The winsock api NORMALLY wants to block on a socket when you call recv(). Usually this occurs when a socket descriptor to a socket that cannot support this operation is trying to accept a connection on a datagram socket. The Create method on the connect socket is successful.

WSA_QOS_NO_RECEIVERS 11008 QoS no receivers. This message has a slightly different meaning from WSAEAFNOSUPPORT. Left by TN on May 15, 2008 5:07 PM # re: Winsock error 10035 When does ready get set to true in the above example. Socket Error 10054 Connection Reset By Peer No more results can be returned by the WSALookupServiceNext function.

This usually means the local software knows no route to reach the remote host. Socket Error 10053 I tried putting it in the IpPort ReadyToSend event but it never goes in there after an operation would block. SendMessageToAllConnections method is called from each of the three threads as data to send comes.We used “lock” statement to prevent other threads from using the ipdaemon1 instance. I using Socket.Blocking = false.

Subsequent operations fail with WSAECONNRESET. Socket Error Codes Linux WSAHOST_NOT_FOUND 11001 Host not found. SetDataToSend will be called again, successfully. WTF???

  1. WOOHOO . . . ?
  2. On the Start/Stop/Reread tab in LMTOOLS, click Start Server.
  3. WSASYSCALLFAILURE 10107 System call failure.
  4. Left by TN on May 15, 2008 2:49 PM # re: Winsock error 10035 TN - I cannot reproduce this here.
  5. WSASERVICE_NOT_FOUND 10108 Service not found.
  6. If you receive the error again, the configuration of the service could be incorrect.
  7. Can you email me your sample code?
  8. Causes: The most common causes of this error are that the license server has not been started or thehostname and mac address inthelicense file does not match that of the server.
  9. Reply With Quote Mar 4th, 2009,07:42 PM #12 pannam View Profile View Forum Posts Thread Starter Hyperactive Member Join Date Feb 2008 Posts 327 Re: [winsock] error 10035 now, all's working

Socket Error 10053

A blocking operation was interrupted by a call to WSACancelBlockingCall. You're trying to send data through the socket to the remotehost, but the remotehost input buffer is full (because its receiving data slower than you're sending it). What Is A Socket Error WSAEREFUSED 10112 Database query was refused. Socket Error 10038 Products: AutoCAD;VIZ Versions: 2006;2007;2008 Article ID: kA230000000taxr Related Articles AutoCAD Forum Connect with peers and Autodesk in our forums, read community articles, and submit your ideas.

This could be due to an out of memory error or to an internal QoS provider error. Since it occurs on the server side only you have no way of knowing this on the client side so I do not know how you could repeat the call. A connect request was made on an already-connected socket. WSA_NOT_ENOUGH_MEMORY 8 Insufficient memory available. Socket Error 10049

If an error occurs at the server side an error should also occur at the client side. WSAECONNABORTED 10053 Software caused connection abort. A reserved policy element was found in the QoS provider-specific buffer.   Requirements Header Winsock2.h; Winerror.h See also Error Codes - errno, h_errno and WSAGetLastError Handling Winsock Errors FormatMessage WSAGetLastError   i rechecked and rechecked my codes and i found out that although different socks from the client are being connected to different socks in the server ..

An application attempts to use an event object, but the specified handle is not valid. Socket Error 10061 Connection Refused We have 3 threads that send data using the method above.How can I synchronize the usage of method. An invalid QoS provider-specific buffer.

as the socks on the client side send data the data arrival in the server is fired only after all the socks in the client side sends the data..

Now, our problem is: when we send the information using this method, some bytes of the information are sent and the winsock buffer of either the client or server side becomes thank you.. This error may also result if a connection was broken due to keep-alive activity detecting a failure while one or more operations are in progress. Socket Error 11001 Some components may not be visible.

Left by Lance on Jan 27, 2009 12:10 PM # re: Winsock error 10035 Dear Lance,We installed the new version. EF Code First Migrations–Create Index with INCLUDE How to enumerate an ENUM (C#) Register Help Remember Me? What is the equivalent method of ipport.InBufferSize in ipport in .NET?I'm not sure of the version. Windows Sockets only allows a single blocking operation—per- task or thread—to be outstanding, and if any other function call is made (whether or not it references that or any other socket)

WSA_QOS_RECEIVERS 11005 QoS receivers. A call to the WSALookupServiceEnd function was made while this call was still processing. This error is returned by WSAStartup if the Windows Sockets implementation cannot function at this time because the underlying system it uses to provide network services is currently unavailable.

© Copyright 2017 All rights reserved.